The XD-II type multi tube cyclone dust collector produced by Hebei Chuang Environmental Protection Equipment Co., Ltd. has dust cleaning control:

The dust collector adopts a PLC control system, and according to different processing techniques, pressure difference control and timed control can be selected for back blowing and dust cleaning. The pressure difference control mechanism is based on the resistance value of the dust collector to open and close the reverse blowing process. When the resistance of the dust collector reaches the preset value for dust cleaning start-up, usually 1200-1500Pa, a control signal is issued to start the blowback cycle. The dust collector repeats the cycle of "cleaning settling filtering" unit by unit until the resistance of the dust collector decreases to the set lower limit of 1000Pa. The pressure difference control mechanism can keep the resistance of the dust collector within a certain range, so that the dust collector can maintain good dust removal efficiency and low operating energy consumption.

Timed control refers to arranging timed blowback based on empirical values, generally used to handle systems with relatively stable operating conditions.

The XD-II type multi tube cyclone dust collector produced by Hebei Chuang Environmental Protection Equipment Co., Ltd. has a small footprint: the filter length is 6 meters, and the filtration wind speed can be selected between 1m/min and 1.5m/min, occupying a smaller footprint than conventional anti blowing bag filters. Control technology: The programmable controller used in the electrical control system has four optional functions: online cleaning, offline cleaning, constant pressure differential cleaning, and timed cleaning. And it has pressure and temperature detection system and manual control mode. High performance, long service life, and easy on-site adjustment. Easy operation and maintenance: The filter bag mouth adopts an elastic expansion ring, which can be directly embedded on the flower board, both sealed and easy to disassemble, reducing the labor intensity of operators.

The XD-II multi tube cyclone dust collector produced by Hebei Chuang Environmental Protection Equipment Co., Ltd. is an improved new type of pulse dust collector based on the dust collector. It combines the advantages of various pulse jet dust collectors with chamber back blowing, overcomes the shortcomings of insufficient chamber dust cleaning intensity and uneven distribution of inlet and outlet air, and expands the application range. The structure of the dust collector has its own characteristics, which improves the dust collection efficiency, adaptability, and extends the service life of the filter bag. Through production practice, the equipment operates stably, requires minimal maintenance, and has a wide range of combinations, receiving high praise from users. This series of products can be widely used in dust and smoke collection systems for metallurgy, mining, building materials, casting, chemical industry, tobacco, asphalt, cement, machinery, grain, mechanical processing, etc. The material of the dust collector filter bag is generally polyester needle punched felt, which allows continuous use temperature ≤ 120 ℃. If the filter bag uses Metas high-temperature needle punched felt, its allowable use temperature can reach 204 ℃.

If the temperature of the treated exhaust gas is higher than the allowable temperature of the filter material mentioned above, cooling measures should be taken before the exhaust gas enters the dust collector. This series of dust collectors can be combined with various specifications of electromagnetic valves according to different specifications. This series of dust collectors can operate under negative or positive pressure without any changes to their body structure. The dust collection efficiency is above, and the purified gas has a dust concentration of less than 100mg/m3. If this series of dust collectors is used in cold areas or when the flue gas is below zero, insulation and heating devices need to be added, and the shell should also be subjected to phase strain. It is a type of dust collector with a dust removal efficiency of above, and the resistance of the dust collector body is less than 900Pa. With the existing boiler induced draft fan, the boiler can operate normally. This dust collector has good load adaptability.

The cyclone element in the XD-II multi tube cyclone dust collector produced by Hebei Chuang Environmental Protection Equipment Co., Ltd. is made of cast iron or ceramic, with a thickness greater than 6mm, therefore it has good performance. It is an ideal equipment for industrial boiler flue gas dust removal and other dust control.

Application and characteristics of ceramic multi tube cyclone dust collector:

1. The installation and management of ceramic multi tube cyclone dust collectors are convenient, and maintenance is simple Save maintenance costs, this dust collector basically does not require maintenance.

2. Suitable for dust control of industrial boilers and thermal power station boilers of various models and combustion methods Such as chain furnace, reciprocating furnace, boiling furnace, coal throwing machine furnace, coal powder furnace, sulfide bed furnace, etc.

3. For other industrial dust, cyclone dust collectors can also be used for treatment, and multi tube cyclone dust collectors can be used for the recovery of cement and other practical dust.

4. Less one-time investment Compared with electrostatic precipitators, this dust collector has a lower total investment. Compared with water film dust collectors, it does not require circulating water, has no secondary head, no wastewater discharge, and does not require additional water treatment equipment.

5. The ceramic core of the ceramic multi tube cyclone dust collector is smooth and will not cause blockage due to its high air volume and strong load adaptability Small footprint, can be installed flexibly according to the user's site conditions and local conditions It can be placed indoors or outdoors.