rule grid

inside Rong

An pretend use ruler inch

studio dimensions

800×800×1000mm(Width x Depth x Height)

Dimensions approximately

1100*1200+Control box width 210*1490+motor height 270mm(Width x Depth x Height)

base

4 mobile casters, positioning feet

material rack

inner part4Layer, configuration4A stainless steelSteel punched plate

Lord want skill technique ginseng number

On site environmental conditions

Temperature:5-40℃ Relative humidity: not greater than85% Suitable for indoor use

There is no strong vibration or airflow around No corrosive gases or chemicals present

Non drying flammable and explosive materials

TSQJ-600 Installation Filter Cleanliness Parameters

Equipped with a high-temperature resistant and high-efficiency filter, the filter is composed of a 304 stainless steel shell and aluminum foil spacers. Washable, high temperature resistant to 250 degrees, cleanliness: efficient filtration 99.99%

Equipment Composition

Composed of furnace body, hot air circulation system, electric heating system, intake and exhaust system, circuit control system, etc

electricity source

3N+PE 380V 50Hz

warm-up time

≤ 30 minutes, empty furnace test

Temperature range for use

Room temperature~250 ℃ (adjustable arbitrarily)

Temperature Uniformity

≤±2.5％℃[national standard]

temperature fluctuation

≤±1℃;[national standard]

heating power

12kw

insulation thickness

100mmleft and right

Surface temperature rise

The national standard is room temperature+35℃

stove body be unify knot constitute

structural form

Adopting a monolithic structure.Concentrated placement

Opening method

Front single door of furnace body.(The door lock adopts chrome plated sheep horn handle and steel hinge)

Furnace shell

Q235After rust prevention treatment, cold-rolled steel plates are sprayed with acrylic self drying paint

Furnace inner liner

304 stainless steel thickness 1.0mm

Shell skeleton

Q235Rust removal and rust prevention treatment for channel steel and angle steel

Inner liner skeleton

Q235After rust removal and rust prevention treatment of angle steel, spray coatingW61Series of silicone heat-resistant paint

bottom plate

Q235After rust removal and rust prevention treatment of channel steel, spray coating851Moisture resistant coating.

thermal insulation material

Low thermal conductivity, high-quality high-temperature resistant aluminum silicate cotton

sealing material

Silicone rubber environmentally friendly sealing strip

drum wind be unify

Working Principle:

The air is blown into the air duct through a filter by a high air volume blower, and then exchanges heat with the electric heating elements in the duct before being blown out from the air outlet. After entering the working chamber and exchanging heat with the workpiece, it returns to the blower motor through the top return air plate, thus forming a continuous hot air cycle. Simultaneously using porous plates for air volume regulation ensures good temperature uniformity within the workspace.

air supply mode

Studio hot air supply method: strong pressure vertical and horizontal air supply

Blower motor

High temperature resistant long shaft motor specifically designed for curing furnaces, with a noise level of65dBthe following

Blast power

1400 RPM, 750W fan

Installation position of motor

Set at the top of the furnace body

enter\\\\exhaust system

intake valve

One top fan base air inlet with a diameter of 60MM

exhaust valve

One manual exhaust valve is installed in front of the top (adjustable in size according to the required exhaust volume). The supplier reserves flange interfaces,

The external exhaust pipe is customized according to the actual situation of the workshop.

electricity control be unify

control manufacture cabinet

Adopting an independent control cabinet for control, the surface of the control cabinet is treated with spraying and painting.

Lord control table

Digital display intelligent instrument XGQ-A2300FAutomatic temperature control, constant temperature and beltPIDAdjust. Control accuracy ±1℃.(The instrument comes with over temperature protection)

Time setting device:

HS48S-99.99 timing device, with a maximum adjustable time of 9999H during actual setting. It can be manually/automatically switched on and off. When the temperature reaches the set temperature, the timer starts. When the set time is reached, the heating power is cut off, and the fan does not stop rotating, helping to dissipate heat inside the box.

electrical components

Adopting domestic and foreign famous brands, such as Chint, Omron, etc

heating control

Suzhou Integrated ElectronicsSSRSolid state relays have contactless power regulation and use input stages with optoelectronic isolation,

TTLLevel compatible input, DC or pulse triggered, with no contacts and no mechanical moving parts,

No sparks, no movement noise, vibration resistance, long lifespan and other characteristics.

guarantee

protect

be

unify

match

place

● Automatically cut off the heating power supply.

● Overtemperature protection: If the specified temperature is exceeded, the buzzer will sound an alarm and the heating will be cut off.

● Motor and heating interlock control Start with the blower before heating to prevent the heater from burning out and causing accidents.

● Motor overload protection Prevent the motor from burning out and tripping.

● Short circuit protection for electric heaters Prevent electric heaters from short circuiting and burning out

● Control circuit protection Prevent short circuits in the circuit and prevent accidents

● circuit breaker Prevent overload and short circuit of the main circuit, which may cause accidents

● Power prevention after power outage Prevent damage to baked goods caused by increased baking time after power on

solid transform stove Appendix document and its it say bright

Yan color

Computer gray white

random file

Instruction Manual1copy/Taiwan

Various instrument manuals1set/Taiwan